Your

I was kind of getting really desperate, as I usually, IMO, take good care of the machine. And usually I know hoe to solve issues. But in hindsight, and after checking timestamps, I do believe it is the slicer. When I updated it earlier this year I printed some figs, but couldn’t troubleshoot during to time constraints, and I parked it. So recently I picked up printing some more, but it didn’t connect immediately.

So yeah, I blame the slicer, and my lack of time.

Thanks for taking the time to reply.

I eventually ended up removing my slicer (Chitubox basic) and install the latest and greatest after cleaning up my profile. So literally starting anew.

Aside from changing te resin, I didn’t modify any other settings to begin with, so my config was rather vanilla.

After taking these steps (and cleaning the z-axis and replacing the nofep again) everything seems to be working fine now.

Cleaning the axis and a new nofep didn’t seem to do anything, so I think it was just a crappy version of the slicer.

Thanks for taking the time to reply.

I eventually ended up removing my slicer (Chitubox basic) and install the latest and greatest after cleaning up my profile. So literally starting anew.

Aside from changing te resin, I didn’t modify any other settings to begin with, so my config was rather vanilla.

After taking these steps (and cleaning the z-axis and replacing the nofep again) everything seems to be working fine now.

Cleaning the axis and a new nofep didn’t seem to do anything, so I think it was just a crappy version of the slicer.

Hey, I cleaned the z-axis: no change I replaced the nofep (again): no change I removed my old slicer (Chitubox Basic 1.9.5) and installed the latest (2.1). I cleaned up my profile, so it was vanilla config: what do you know: it seems to work now!

Still running some prints to monitor any changes, but it’s looking good!

Thank you for your time!

Thanks for taking the time to reply.

I eventually ended up removing my slicer (Chitubox basic) and install the latest and greatest after cleaning up my profile. So literally starting anew.

Aside from changing te resin, I didn’t modify any other settings to begin with, so my config was rather vanilla.

After taking these steps (and cleaning the z-axis and replacing the nofep again) everything seems to be working fine now.

Cleaning the axis and a new nofep didn’t seem to do anything, so I think it was just a crappy version of the slicer.

Thanks for taking the time to reply.

I eventually ended up removing my slicer (Chitubox basic) and install the latest and greatest after cleaning up my profile. So literally starting anew.

Aside from changing te resin, I didn’t modify any other settings to begin with, so my config was rather vanilla.

After taking these steps (and cleaning the z-axis and replacing the nofep again) everything seems to be working fine now.

Cleaning the axis and a new nofep didn’t seem to do anything, so I think it was just a crappy version of the slicer.

Thanks for taking the time to reply.

I eventually ended up removing my slicer (Chitubox basic) and install the latest and greatest after cleaning up my profile. So literally starting anew.

Aside from changing te resin, I didn’t modify any other settings to begin with, so my config was rather vanilla.

After taking these steps (and cleaning the z-axis and replacing the nofep again) everything seems to be working fine now.

Cleaning the axis and a new nofep didn’t seem to do anything, so I think it was just a crappy version of the slicer.

Well, it seems you might be right.

I installed the latest version of Chitubox Basic (2.1) and now it works just great.

Thank you very much, kind internet stranger!

The glass is half full, yeah? 😉

So you think is is maybe a software issue?

I’ll check if there are any known issues and possibly update my chitubox

I did select different settings for the other resin. I checked both in the app and on Epax’s website, and my settings are aligned

Thank you for your reply! I hadn’t thought of the mechanics!

I’ll check the screw and clean it.

Oh cool, implementing mediocre algorithms. What could possibly go wrong?

Khandar Estrada khandos thrus indactu nosfrandus khandar dematos… erh blah lahblah

Ise kde, not gnome.

Aside from the obvious (company providing all the necessary tools) why not using libreoffice and saving it as M$ excel?

Surprise… Surprise… It’s a snap!

dnf upgrade And package-cleanup --cleandupes Should have fixed it.

You may also want to check up on regulations and laws of your country.

In Belgium, for instance, I am responsible for any and all attacks originating from my PC. If you were hacked and said hackers used your computer to stage an attack, the burden of proof is upon you. So instead of hiring very expensive people to trace the real source of an attack originating from your own PC, enabling a firewall just makes sense, besides making it harder on hackers…